Sdc S6100 SERIES REVERSIBLE PANIC/FIRE EXIT Manual do Utilizador

INSTALLATION INSTRUCTIONS801 Avenida Acaso, Camarillo, Ca. 93012• (805) 494-0622 • www.sdcsecurity.comE-mail: [email protected] SERIESREV

P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 6STEP 4: INSTALL TOP ROD AND TOP STRIKE1. Mount the top latch as

P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 76. Mark and drill mounting holes on the jamb for the top strike

Door HandingUse this diagram to determine the hand of door.NOTE:To extend the life of this device, it is recommended to activate the dogging feature d

INSTALLATION INSTRUCTIONS801 Avenida Acaso, Camarillo, Ca. 93012• (805) 494-0622 • www.sdcsecurity.comE-mail: [email protected] SERIESPAN

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 2DESIGNATION OF PARTSTop Strike Fixing PlateTop Strike(Back View

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 3A. PREPARE DOOR 1. Mark centerline of device by drawin

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 4B. ASSEMBLE RODS AND LATCHES1. Screw bottom rod into bottom lat

C. MOUNT LATCH ASSEMBLIES1. Attach latch mounting brackets to top and bottom latch assemblies2. Insert top latch assembly into top of the door and fas

3. Adjustment procedure:Adjust the length of the two vertical rods by hand through the cut-outs (figure 4-2).Shorten or lengthen the rods by turning i

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 73. Cut the length if required:a. The device length is pre-cut f

P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 2A. DESIGNATION OF PARTSB. TYPE OF INSTALLATIONA. Single Door

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 82. Release push bar, Make sure both top and bottom latch bolts

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 9I. INSTALL BOTTOM STRIKE1. Bore the hole into the finished floo

P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 10Door HandingUse this diagram to determine the hand of door.NOT

P:\INSTALLATION INST\SWITCH KITS\INST-S6000-ATS.vsd REV - 04-12 Page 1Any suggestions or comments to this instruction or product are welco

P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 3STOP LINEJambof DeviceStrikeLCStrikeSiteDoorD. INSTALL STRIKE

P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 4H. INSTALL COVERSNOTE: The Device bar has 3 different lengths;S

INSTALLATION INSTRUCTIONS801 Avenida Acaso, Camarillo, Ca. 93012• (805) 494-0622 • www.sdcsecurity.comE-mail: [email protected] SERIESPAN

P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01/11 Page 2DESIGNATION OF PARTSTop Strike Fixing PlateTop Strike(Back View

P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 3STEP 1: PREPARE DOOR1. Mark position of holes on the door per

STEP 2: INSTALL BRACKETS, DEVICE & TRIM1. Remove chassis cover from chassis assembly and end cap from end cap bracket.2. Cut the length if requ

P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 5STEP 3: INSTALL BOTTOM ROD AND BOTTOM STRIKE1. Mount the bottom